Loading...
Technical Insight

Magazine Feature
This article was originally featured in the edition:
Issue 5 2026

Enabling high-volume silicon photonics through advanced test

News

Advanced photonic test is becoming critical to scaling silicon photonics for AI and HPC, with automated optical alignment, integrated electrical and optical measurements, and wafer-level testing.

By Aether Lee, Global Photonics Center of Excellence Manager, Advantest

With the explosive growth of artificial intelligence (AI) and high-performance computing (HPC), the requirements for data center connectivity are changing rapidly. AI training and inference systems must move enormous quantities of data among processors, memory and networking infrastructure, creating demands for bandwidth density and energy efficiency that are becoming increasingly difficult to meet with conventional electrical interconnects and traditional pluggable optical architectures. The industry is consequently moving toward silicon photonics and, increasingly, near- and co-packaged optics (NPO/CPO), where photonic components are placed close to or within the switch or ASIC package.

But scaling silicon photonics is not simply a matter of designing better photonic integrated circuits (PICs). As PIC complexity and manufacturing volumes increase, test is becoming a critical part of the manufacturing strategy. Accurate, repeatable wafer-level testing can identify known-good die (KGD) earlier, provide data for yield improvement and prevent costly downstream processing of defective devices. The challenge is doing all of this at production-worthy throughput.

Unlike conventional semiconductor test, PIC testing requires simultaneous management of two domains. Electrical signals must be applied and measured and light must be accurately delivered to and collected from structures that can be highly sensitive to position, angle, wavelength and polarization. Automated optical alignment, precise positioning and tightly integrated electrical and optical instrumentation are thus fundamental requirements for high-volume manufacturing (HVM).

Alignment becomes a manufacturing challenge
One of the most significant differences between electrical IC testing and photonic testing is the need to establish a repeatable optical connection to every device under test. Electrical wafer probing benefits from mature probe-card technology and well-defined contact structures. In photonics, however, a fiber array unit (FAU), as shown in Figure 1, must couple light into and out of grating couplers or other optical interfaces on the PIC. Small variations in position can translate directly into optical loss and measurement variation. The problem therefore extends beyond simply finding the device: the test system must find the point of optimum optical coupling quickly and consistently.


Figure 1: The FAU shown here uses a visual/imaging process to bring the FAU to the grating couplers on the PIC, allowing it to look for light in a larger area.

An HVM-capable approach begins by using machine vision to bring the FAU close to the grating couplers and establish “first light.” From there, the system can perform an area scan followed by a gradient search to determine the optimum X-Y position. Fine positioning can then locate the local optical-power peak. In one implementation, a piezo-based nanopositioning stage supports a 100 × 100 µm scan range, with an area scan requiring a few seconds and a local gradient search approximately one second.

But X and Y are only part of the problem. Optimum coupling can require control across six degrees of freedom: X, Y and Z positioning plus U, V and W rotation. A high-performance digital imaging system, six-degree-of-freedom hexapod positioning platform and nanopositioning stage can therefore work together to provide coarse and fine alignment (see Figure 2).

The rotational axes are particularly important. Adjusting the W angle can help maximize beam coverage on the grating coupler and minimize channel-to-channel power variation. U and V alignment is more complex because both can influence insertion loss and center wavelength. Consequently, a production test methodology must optimize the complete optical interface rather than treating alignment as a simple two-dimensional positioning problem.


Figure 2: The FAU actuator system shown here implements X, Y and Z positioning together with U, V and W rotation, providing optimal six-degree-of-freedom positioning and alignment.

Making optical measurements repeatable
Finding maximum optical power is only useful if the resulting measurement accurately represents the device rather than variations in the test setup. That makes calibration, loss compensation and polarization management essential. An optical loopback, for example, can provide a known path through which transmitted light returns to an optical power meter, allowing alignment to be verified by measuring returned optical power. Multiple grating couplers can also be designated as reference channels to improve consistency across channels.

Polarization adds another variable. The optical response of a PIC can change with the polarization state of the incoming light, potentially making test results dependent on the test setup rather than solely on device performance. These capabilities matter because PIC production involves much more than a simple pass/fail optical continuity check. As shown in Figure 3, typical measurements can include insertion loss and channel-to-channel conformity as well as device-specific characterization. A variable optical attenuator (VOA), for example, can be tested for optical attenuation versus applied current and for the current required to achieve a target attenuation. Photodetector testing can correlate input optical power with electrical current and measure responsivity as a function of wavelength.

Ring modulators present another example. Their intrinsic optical characteristics, together with those of the grating coupler, can be measured optically without electrically probing the wafer. Wavelength sweep data can be curve-fitted to derive the grating coupler’s center wavelength, while removing the fitted baseline reveals ripple in the measurement.


Figure 3: The typical optical tests shown here are essential to ensuring successful PIC production.

Bringing electrical and optical test together
At the same time, photonic manufacturing cannot afford to treat electrical and optical testing as completely separate operations. The PIC is increasingly part of an electro-optical system, and HVM economics favor a test architecture that can handle both domains efficiently.

One opportunity is to use optical alignment time productively. Electrical alignment is performed before optical alignment, allowing continuity and potentially other purely electrical tests to run while automated optical probe alignment is taking place. This parallelism can turn what otherwise would be idle test time into productive measurement time.

Dark-current measurement is another important electrical test, particularly for photodetectors. Because typical monitor-photodiode dark currents can be in the nanoampere to sub-nanoampere range, instrumentation must provide the sensitivity and guarding needed to measure very small currents accurately.

The larger manufacturing opportunity comes from integrating optical instruments into the same automated test environment used for electrical testing. Rather than controlling lasers, power meters and other optical equipment through separate test programs, an optical control library can provide test-method interfaces within the semiconductor test software environment. The approach supports optical instruments from multiple suppliers while providing built-in calibration and compensation functions.

This convergence is important for throughput, but it also addresses another HVM requirement: consistency. As the number of instruments, measurements and test steps grows, manual setup and independent software environments create opportunities for configuration errors and test-to-test variation. Coordinated software control makes calibration, compensation and measurement sequencing part of an automated production flow.


Figure 4: The V93000-TRITON Photonic Test Solution is a novel, integrated test solution optimized for high-volume, single-sided wafer-level probing to support scalable production of photonic devices.

Test earlier to protect yield
Wafer-level photonic test also has implications beyond test time itself. NPO, CPO and other advanced photonic systems combine multiple valuable components. A defective PIC discovered after assembly may mean losing not only that die but also the value added through packaging and integration. Establishing device performance before those later manufacturing stages therefore becomes increasingly important as integration complexity rises.

Industry work on NPO & CPO test methodology reflects this need for testing throughout the manufacturing hierarchy. Test can occur at PIC and electronic IC wafer level, after die singulation for known-good-die screening, at the assembled optical-engine level and ultimately at the completed co-packaged unit and system levels.

Wafer-level test provides the earliest opportunity to generate meaningful production data. Measurements of optical loss, wavelengthbehaviour, detector responsivity, modulator performance and electrical characteristics can identify defective devices before expensive packaging steps while also feeding information back to wafer fabrication.

That data becomes particularly valuable during the transition from development to volume manufacturing. Production test is no longer simply an inspection step at the end of fabrication; it becomes part of the yield-learning loop.

Stable, automated measurement enables manufacturers to distinguish actual process variation from variation introduced by alignment or instrumentation.

An ecosystem solution
No single company controls all of the technologies required for photonic production test. PIC designers define optical interfaces and device characteristics. Foundries determine process capabilities and manufacturing variation. Probe and positioning specialists provide precision optical access. Instrumentation suppliers provide lasers, power meters and other measurement technologies. Packaging companies must ultimately integrate known-good devices into increasingly complex assemblies, while automated-test specialists must bring these elements together in a repeatable production environment. An example of such an environment is shown in Figure 4—the V93000-TRITON Photonic Test Solution, developed collaboratively by Advantest and FormFactor.

The importance of interoperability will only grow as silicon photonics moves toward higher volume. Industry efforts already envision test and measurement spanning wafer/die, component, optical-engine, co-packaged-unit and system levels, with an emphasis on ensuring that measurements performed by different vendors, on different equipment and in different facilities have consistent meaning.

This requirement changes the role of test. The objective is not simply to measure more photonic parameters. It is to create a manufacturing infrastructure in which optical and electrical measurements are automated, repeatable and scalable.

Silicon photonics promises to remove one of the major bottlenecks confronting AI infrastructure: moving ever-growing quantities of data without allowing interconnect power and complexity to become unsustainable. Realizing that promise at scale, however, depends on being able to manufacture sophisticated PICs economically.

This makes test a key technology enabling the transition. Automated optical alignment, submicron positioning, multi-axis coupling optimization, polarization management, integrated optical instrumentation and parallel electrical/optical test can transform photonic characterization from a laboratory-intensive process into a repeatable production operation. Just as automated test became indispensable to the economics of semiconductor manufacturing, advanced photonic test will increasingly determine how quickly silicon photonics can move from promising technology to high-volume infrastructure.


Logo
x